need full dump sb5101u 2mb with spi mx chip - Printable Version +- Haxorware Forums (http://www.haxorware.com/forums) +-- Forum: General (http://www.haxorware.com/forums/forumdisplay.php?fid=6) +--- Forum: Modems (http://www.haxorware.com/forums/forumdisplay.php?fid=7) +--- Thread: need full dump sb5101u 2mb with spi mx chip (/showthread.php?tid=1036) |
need full dump sb5101u 2mb with spi mx chip - blacklist - 30-10-2011 I tried SB5101n, gui works perfect but keeps scanning with no luck. thank you RE: need full dump sb5101u 2mb with spi mx chip - drewmerc - 30-10-2011 you just need to change the tuner/annex the only difference between the u and n is ones docsis the other in eurodocsis (i used to have a doc saying exactly what to setting to choose to convert) Code: ---------------------------- anyways at a 2am guess (ok 1am again damn clocks going back fucking uk time) goto the webshell and enter 1 line at a time cd \non cd \hal annex_ B cm_annex 3 write RE: need full dump sb5101u 2mb with spi mx chip - blacklist - 30-10-2011 And where do I use those commands,? I used blackcat usb Build 27x with ISP mode.... and what tools do I use or connection. Do I connect via? (USB, Ethernet, or etc....) Thanks alot (30-10-2011, 02:20 AM)drewmerc Wrote: you just need to change the tuner/annex the only difference between the u and n is ones docsis the other in eurodocsis (i used to have a doc saying exactly what to setting to choose to convert) RE: need full dump sb5101u 2mb with spi mx chip - drewmerc - 30-10-2011 in the webshell or telnet RE: need full dump sb5101u 2mb with spi mx chip - blacklist - 30-10-2011 well I Did as it is, but the problem is, doesnt do any action. Attempting Downstream FEC lock @ freq= 226000000 Hz, QAM256 it gives me this message, then it keeps scanning on the right upper side, but when I am sending other commands, all freezes, then I have to reset the unit in order to get in a modem..... do you have any doc shows full detailed information about webshell full command list.? thanks! (30-10-2011, 09:34 AM)drewmerc Wrote: in the webshell or telnet RE: need full dump sb5101u 2mb with spi mx chip - drewmerc - 30-10-2011 still scanning do this cd \cm_hal scan_stop cd \ it's better to do these commands in telnet as you get a better response (really how can you people really get by without using telnet) if you find a full list of commands with explanations i'd love a copy (i have a full list just no explanations) RE: need full dump sb5101u 2mb with spi mx chip - blacklist - 31-10-2011 Here is the situation I am in CM HAL Settings: --------------- Downstream Tuner Type = 19 (BCM3419) Upstream Amp Type = 9 (BCM INTERNAL AMP) Downstream Reference Frequency = 24000000 hz Upstream Reference Frequency = 24000000 hz Input Frequency to PHY = 4000000 hz Annex Mode = ANNEX B Spreader Scale = 1 Upstream Sample Frequency = 432000000 hz 1024QAM Enabled = 0 Use DOCSIS 2.0 Clipping = 1 Proprietary SCDMA Code Matrix Enabled = 0 Advance Map RunAhead Enabled = 1 Upstream Priority Queue Support Enable = 1 DS_AGI = 0xd DS_AGT = 0x1d STATHR = 0x400 STAGI = 0 STPGA1 = 0x20042 STAGT = 0xfff00000 STABW1 = 0xd0b STABW2 = 0x409 Number of SHACK Tries = 3 Power save mode enabled = 0 Optimized 3420 frequency map enabled = 1 High output PA enabled = 0 I am in Los Angeles Area, Can anyone sent me the correct signal config in this format?, I am using SB5101U model Thanks alot for the answers (30-10-2011, 09:53 AM)drewmerc Wrote: still scanning do this RE: need full dump sb5101u 2mb with spi mx chip - drewmerc - 31-10-2011 after an interesting half-hour search i now understand that i was wrong as i always thought the differences between the n and u were docsis and euro docsis but they are not it's simply 1 has a usb port (they are set for both docsis's from new) well i find it interesting but that does not help you problem, so i'll fall back to the universal question of modems are your certs valid? RE: need full dump sb5101u 2mb with spi mx chip - blacklist - 31-10-2011 Yes it is. (31-10-2011, 07:48 AM)drewmerc Wrote: after an interesting half-hour search i now understand that i was wrong as i always thought the differences between the n and u were docsis and euro docsis but they are not it's simply 1 has a usb port (they are set for both docsis's from new) |