Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
please help out a newb sb5101
#11
ok, finally got around to this again. could not get the 5101 to work with subbed 5100 flash, so i bought a 5100 and flashed it with the subbed 5100. NOW here comes the problems... i had it working fine, so i then added the haxoware firmware and now there seems to be a problem...
LibUsbDotNet version: 2.2.8.104
BlackcatUSB Script Engine running, build: 200
Welcome to BlackcatUSB interfacing software, build: 300
Running on: Microsoft Windows 7 Professional (32 bit)
Initializing EJTAG engine
Device connected in JTAG mode: 7.01
JTAG engine setup successfully
Detected CPU ID: 0x334817F IMP CODE: 0x800908
Manufacturer ID: 0xBF Part ID: 0x3348
EJTAG Version support: 2.0
Target device supports DMA mode
Checking for a device specific script to automatically load
Loading device specific script: SB5100_JTAG.bcs
Loading script: SB5100_JTAG.bcs
MemoryInit: Failed - device parameters failed Init
Setting device parameter (Intel Flash delay) to 0x64
Setting device parameter (AMD Flash delay) to 0xFA
Setting device parameter (Memory Read Delay) to 0x64
Error in script SB5100_JTAG.bcs on line 21
Reason: Error processing: CFGFLASH
Script file (SB5100_JTAG.bcs) unloaded
Disconnected from BlackcatUSB
Device connected in DFU bootloader mode
Sending AVR DFU erase command
AVR DFU command successful
Beginning AVR flash write (12898 bytes)
AVR flash written successfully
Disconnected from BlackcatUSB
Initializing EJTAG engine
Device connected in JTAG mode: 7.01
JTAG engine setup successfully
Detected CPU ID: 0x334817F IMP CODE: 0x800908
Manufacturer ID: 0xBF Part ID: 0x3348
EJTAG Version support: 2.0
Target device supports DMA mode
Checking for a device specific script to automatically load
Loading device specific script: SB5100_JTAG.bcs
Loading script: SB5100_JTAG.bcs
MemoryInit: Failed - device parameters failed Init
Setting device parameter (Intel Flash delay) to 0x64
Setting device parameter (AMD Flash delay) to 0xFA
Setting device parameter (Memory Read Delay) to 0x64
Error in script SB5100_JTAG.bcs on line 21
Reason: Error processing: CFGFLASH
Reply
#12
haxorware wont work on a 5100 you need to use 5100mod
__________________________________________________________________________________
******new discord chat linkĀ https://discord.gg/5BQQbsb*******
Reply
#13
is there any info on unbricking with blackcat? i think i bricked it by using the wrong haxoware. when i start up the usb blackcat program i only get 3 tabs now... status - console - memory.
Reply
#14
saving myself from typing soi'll just copy paste a pm from this morning

Halfwit Wrote:
drewmerc Wrote:
Halfwit Wrote:Ok Ive bricked another 5101 it was a bad flash.
I only own a blackcat usb jtag . How can I debrick it? Im a noob when it comes to this.
I really cant seem to find anything on the web when it comes to the 5101 and blackcat

last time i try to help debrick with BcUsb it was without success http://www.haxorware.com/forums/thread-1...hard+reset

but as noted in my last reply in that thread there is not support for PrAcc Mode
which should allow poke'ing i think you should email the makers and ask http://www.embeddedcomputers.net/products/BlackcatUSB/
I just purchased a brand new BC UsbJtag and followed your directions used RC15 with 304 software.
Worked for me thank you very much. Im not sure if when you hit detect it pokes the memory now . It worked though . Thanks
__________________________________________________________________________________
******new discord chat linkĀ https://discord.gg/5BQQbsb*******
Reply
#15
(15-01-2012, 06:56 PM)drewmerc Wrote: saving myself from typing soi'll just copy paste a pm from this morning

Halfwit Wrote:
drewmerc Wrote:
Halfwit Wrote:Ok Ive bricked another 5101 it was a bad flash.
I only own a blackcat usb jtag . How can I debrick it? Im a noob when it comes to this.
I really cant seem to find anything on the web when it comes to the 5101 and blackcat

last time i try to help debrick with BcUsb it was without success http://www.haxorware.com/forums/thread-1...hard+reset

but as noted in my last reply in that thread there is not support for PrAcc Mode
which should allow poke'ing i think you should email the makers and ask http://www.embeddedcomputers.net/products/BlackcatUSB/
I just purchased a brand new BC UsbJtag and followed your directions used RC15 with 304 software.
Worked for me thank you very much. Im not sure if when you hit detect it pokes the memory now . It worked though . Thanks

according to there site (build 302), it does support PrAcc? do you have any links or instructions on debricking this modem? i've read alot, but couldn't find anything about if you don't have all the tabs showing? like i mentioned i'm only showing (status) - (console) - (memory) and in the console window it says... Error processing: CFGFLASH
Reply
#16
I am having sort of the same problem with my blackcatusb pcb 1.8 it will not detect my sb5100 i am using 326 any help or tutorials u can point me to the previous version 1.7 works fine
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)