Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
How to flash haxorware to sb5101 and dpc2100r2?
#11
(13-09-2012, 12:19 AM)conazo Wrote: Does anyone know if this firmware version works with ethernet cable one click method v2.0.2r1256-071128a-PCM ????

Spend the 60 bucks and use usbjtagnt. I have been
using it for years without a problem. It can also be used
for the 3.0 docis modems. Unfortunately no Haxomatic
in production.
Reply
#12
(13-09-2012, 08:35 PM)haroldstein Wrote:
(13-09-2012, 12:19 AM)conazo Wrote: Does anyone know if this firmware version works with ethernet cable one click method v2.0.2r1256-071128a-PCM ????

Spend the 60 bucks and use usbjtagnt. I have been
using it for years without a problem. It can also be used
for the 3.0 docis modems. Unfortunately no Haxomatic
in production.
yes but if board 8 pin holes are soldered then nothing can be done im i correct?
Reply
#13
Solder sucker and soldering iron will fix that for ya
Or if your good flux and braided copper wire will suck up the solder too
Reply
#14
(13-09-2012, 09:54 PM)conazo Wrote:
(13-09-2012, 08:35 PM)haroldstein Wrote:
(13-09-2012, 12:19 AM)conazo Wrote: Does anyone know if this firmware version works with ethernet cable one click method v2.0.2r1256-071128a-PCM ????

Spend the 60 bucks and use usbjtagnt. I have been
using it for years without a problem. It can also be used
for the 3.0 docis modems. Unfortunately no Haxomatic
in production.
yes but if board 8 pin holes are soldered then nothing can be done im i correct?

buy a solder sucker to suck the solder out, they are only a couple of bucks
or if your cheep like me just solder a short bit of wire to the via and shove it into the jtag cable connector
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply
#15
also, maybe use pogo pins!
http://www.ebay.com/itm/SOIC-8-Spring-Lo...3a50d3c291


Attached Files Thumbnail(s)
   
Reply
#16
pogo pins will work to, hell at one point way back i made my own adapter, just by holding the pins on the via's then adding a lot of hot melt glue all around, worked good too and lasted a good while across many reflashes
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply
#17
so for better understanding, to flash both dpc2100r2 and sb5101 which one do i need 1. Jtag NT or 2.USB TTL to Jtag???
Reply
#18
ttl is different interface. Buy a NT from usbjtag.com about 68.00 shipped from canada.
Reply
#19
(29-08-2012, 08:39 PM)mohitomish Wrote: e are going to Flas the Webstar DPC2100R2 Without open it and only by Ethernet cable!!!!

First install The program net-snmp-5.4.2.1.win32
Make sure that the Firmware is called "haxorware.bin" Copy the Firmware that is in this folder or change the name
of your bin file for (haxorware.bin) And add to the TFTP Folder.

SET UP TCP/IP:
192.168.100.10
255.255.255.0
192.168.100.1

1. Open your TFTP server and be sure that the haxorware.bin is in the Folder:


This method work when is the Modem DPC2100R2 With the firmware ver: v202r1256-060303

Just open The DPC2100R2.bat File and follow the intructions is very easy When You see that the TFTP Server
Finish Sending the bin file wait 5 seconds and reboot the modem!!
And Enjoy Haxorware.


NOTE:
For this method work you need to install First net-snmp-5.4.2.1.win32 add in the folder
And that the TFTP is Ready to Sent the bin File called (haxorware.bin) add in the folder is the last version 11rev39

Thanks To sbhacker.





Where do I get net-snmp-5.4.2.1.win32

(29-08-2012, 08:39 PM)mohitomish Wrote: e are going to Flas the Webstar DPC2100R2 Without open it and only by Ethernet cable!!!!

First install The program net-snmp-5.4.2.1.win32
Make sure that the Firmware is called "haxorware.bin" Copy the Firmware that is in this folder or change the name
of your bin file for (haxorware.bin) And add to the TFTP Folder.

SET UP TCP/IP:
192.168.100.10
255.255.255.0
192.168.100.1

1. Open your TFTP server and be sure that the haxorware.bin is in the Folder:


This method work when is the Modem DPC2100R2 With the firmware ver: v202r1256-060303

Just open The DPC2100R2.bat File and follow the intructions is very easy When You see that the TFTP Server
Finish Sending the bin file wait 5 seconds and reboot the modem!!
And Enjoy Haxorware.


NOTE:
For this method work you need to install First net-snmp-5.4.2.1.win32 add in the folder
And that the TFTP is Ready to Sent the bin File called (haxorware.bin) add in the folder is the last version 11rev39

Thanks To sbhacker.

Where do I get net-snmp-5.4.2.1.win32?
Reply
#20
I bet OP is on his way to becoming a reseller of modded modems. (▀̿Ĺ̯▀̿ ̿)
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)