Thread Rating:
  • 5 Vote(s) - 4 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Arris TG2492 (VM Super hub 3)
#67
Did a bit more reversing today and worked out how to add custom commands to the cli menu. They have a plugin system which dynamically loads shared libraries to add menus and their commands. 

Once you know the structure it's fairly trivial. Just added a custom 'pwnmenu' to run system level commands. I'll probably make a post at some point summarising everything and detailing this further as I have access to pretty much everything at this point.

[Image: DX4TlSC.png]

Also, a list of most of the commands available from the cli

Code:
system               - Go to system Menu.
        startup              - Go to Startup Sub-menu.
                enable               - Enable auto start, execute the startup script.
                disable              - Disable auto start, jump to command line.
                filename             - Setup startup script filename <startup script>.
                docsis               - Enable/Disable DOCSIS <Bool - on/off>.
                default              - Setup default startup script filename and enable auto start.
                show                 - Show current settings.
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        nvram                - Go to NVRAM Sub-menu.
                show                 - List database of a module in a component [component module].
                remove               - Remove a database of a module in a component [component module].
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        environment          - Go to Environment variables Sub-menu.
                printenv             - Print environment variables.
                setenv               - Set an environment variable value [variable value].
                hexgetenv            - Get an environment variable value in hex format [variable].
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        pp                   - Go to Packet Processor Sub-menu.
                brief                - Show global, vpids and sessions summary.
                devs                 - Show counters by network devices.
                disable              - Disable packet processor.
                enable               - Enable  packet processor.
                flush                - Flush all sessions.
                global               - Show global statistics.
                mapper               - <number of sessions [1..2048(all)]> Show connection tracking mapping.
                nopsm                - Take C/Q/M-PDSPs out of Power Save mode.
                noqos                - Disable QoS processing scheme (Debug purpoces only).
                pids                 - Show pids.
                psm                  - Put  C/Q/M-PDSPs into Power Save mode.
                qos                  - Enable  QoS processing scheme (Debug purpoces only).
                qosDiscardOOO        - <[0=ForwardOOO,1=DiscardOOO(default)]> Qos Discard out of order.
                resetStats           - Reset the HIL Analysis stats.
                resetTimeout         - Reset the session timeout to default.
                session              - <"all"> - Shows all active sessions
                       <"wan2lan"> - Shows all WAN-->LAN active sessions
                       <"lan2wan"> - Shows all LAN-->WAN active sessions
                       <"lan2lan"> - Shows all LAN-->LAN active sessions
                       <"mac"> <"da","sa","all"> <MAC Adress> - Shows all sessions matching to MAC SA/DA/both
                       <"ipv4"> <"src","dst","all"> <IP> - Shows all sessions matching to IPv4 SRC/DST/both
                       <"ipv6"> <"src","dst","all"> <IP> - Shows all sessions matching to IPv6 SRC/DST/both
                       <"tcp"> - Shows all TCP active sessions
                       <"udp"> - Shows all UDP active sessions
                       <"dslite"> - Shows all Ds-Lite active sessions
                       <"gre"> - Shows all GRE active sessions
                       <"drop"> - Shows all drop sessions.
                setDsLiteUsFragIPv4  - <DS-Lite US frag method[0=IPv6(default),1=IPv4]> Set the SD-Lite Fragment method.
                setClstMaxCreditByte - <clusterId> <maxCredit> Set the cluster max Byte Global Credit.
                setClstMaxCreditPkt  - <clusterId> <maxCredit> Set the cluster max Pkt Global Credit.
                setQueueItCreditByte - <queueId> <itCredit> Set the queue Iteration Byte Credit.
                setQueueItCreditPkt  - <queueId> <itCredit> Set the queue Iteration Pkt Credit.
                setQueueMaxCreditByte - <queueId> <maxCredit> Set the queue max Byte Credit.
                setQueueMaxCreditPkt - <queueId> <maxCredit> Set the queue max Pkt Credit.
                setReassDbTimeout    - <[2..254]=Timeout in mSEC , 255=Disable timeout> Set the Reassembly DB timeout.
                setSesTimeout        - <Sec> Set the session timeout.
                stats                - Show HIL Analysis report.
                tdoxAckSupprDis      - <[0=Enable(default),1=Disable]> TDOX ACK suppression.
                tdoxDbg              - <[0=Disable,1=Enable]> TDOX debug.
                tdoxDis              - Disable TDOX feature.
                tdoxEn               - Enable TDOX feature.
                tdoxEvalAvgPktSize   - <Bytes> Set the TDOX Evaluation packet size threshold.
                tdoxEvalPPS          - <PPS> Set the TDOX Evaluation packets per second threshold.
                tdoxEvalTime         - <Sec> Set the TDOX Evaluation time.
                test                 - Go to test Menu.
                        createSession        - create the session.
                        printDsPktEgress     - print dsPktDataEngress.
                        printDsPktIngress    - print dsPktDataIngress.
                        printUsPktEgress     - print usPktDataEngress.
                        printUsPktIngress    - print usPktDataIngress.
                        setDsPktEgress       - <pkt AA:BB:CC..> <length> set dsPktDataEgress.
                        setDsPktIngress      - <pkt AA:BB:CC..> <length> set dsPktDataIngress.
                        setUsPktEgress       - <pkt AA:BB:CC..> <length> set usPktDataEgress.
                        setUsPktIngress      - <pkt AA:BB:CC..> <length> set usPktDataIngress.
                        help                 - Display menu commands.
                        shortcuts            - Display key shortcuts help.
                        exit                 - Exit this sub-menu, go to previous menu.
                                                quit                 - Quit and terminate CLI.
                        reboot               - Reboot the system.

                version              - Show Firmware version.
                vpids                - Show counters by vpids.
                vpidEgressList       - <vpid Id> Show egress handles list for specific VPID.
                vpidIngressList      - <vpid Id> Show ingress handles list for specific VPID.
                vpidTcpList          - <vpid Id> Show tcp handles list for specific VPID.
                vpidTdoxList         - <vpid Id> Show tdox handles list for specific VPID.
                xQC                  - <cluster Id> Show QoS Cluster extended data.
                xQQ                  - <queue Id> Show QoS Queue extended data.
                xSession             - <session Id> Show sessions extended data.
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        sme                  - Go to State Machine Engine Sub-menu.
                list                 - List all top-level state machines.
                lshort               - List all state machines [filters].
                llong                - List all state machines with state path [filters].
                SetModule            - Set the LOG module (SM name (partial), Module index, [Component index]).
                SetSeverity          - Set the LOG Severity (SM name (partial), Severity index).
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        l2switch             - Go to L2Switch Sub-menu.
                disableForwarding    - Stops all traffic in l2switch..
                enableForwarding     - Starts traffic in l2switch..
                disablePort          - Stop Rx and Tx on a port.
                       Params:
                               Port number(0-7): 0 = ATOM, 1 = MOCA, 2 = RGMII0, 3 = RGMII1,
                               5 = UDMA0, 6 = UDMA1, 7 = DOCSIS/ARM).
                enablePort           - Starts Rx and Tx on a port.
                       Params:
                               Port number(0-7): 0 = ATOM, 1 = MOCA, 2 = RGMII0, 3 = RGMII1,
                               5 = UDMA0, 6 = UDMA1, 7 = DOCSIS/ARM).
                setPortMode          - Sets MAC gasket mode for a port. Full Duplex is alwyas assumed.
                       Params:
                               Port number(0-7): 0 = ATOM, 1 = MOCA, 2 = RGMII0, 3 = RGMII1,
                               5 = UDMA0, 6 = UDMA1, 7 = DOCSIS/ARM)
                               Mode(0-7): 0 = MII at 10Mbps, 1 = MII at 100 Mbps, 2 = RMII at 10 Mbps,
                               3 = RMII at 100 Mbps, 4 = GMII at 1000 Mbps, 5 = RGMII at 100Mbps,
                               6 = RGMII at 1000Mbps,7 = RGMII at 10Mbps..
                getPortStats         - Get statistic counters for a port.
                       Params:
                               Port number(0-7): 0 = ATOM, 1 = MOCA, 2 = RGMII0, 3 = RGMII1,
                               5 = UDMA0, 6 = UDMA1, 7 = DOCSIS/ARM).
                getProxyStats        - PrxPDSP statistics.
                enableTaggingOnPort  - Mark port as tagged.Tagged ports expect to receive tagged frames.
                       Untagged frames will be assigned to port's Native Vlan.
                       Tagged port always transmits tagged frames.
                       Params:
                               Port number(0-7): 0 = ATOM, 1 = MOCA, 2 = RGMII0, 3 = RGMII1,
                               5 = UDMA0, 6 = UDMA1, 7 = DOCSIS/ARM).
                disableTaggingOnPort - Mark port as untagged.Untagged expect to receive untagged frames.
                       Ttagged frames will be discarded.
                       Untagged port always transmits tagged frames.
                       Params:
                               Port number(0-7): 0 = ATOM, 1 = MOCA, 2 = RGMII0, 3 = RGMII1,
                               5 = UDMA0, 6 = UDMA1, 7 = DOCSIS/ARM).
                setPortNativeVlan    - Set port Native Vlan.Untagged frames will be assigned to this Vlan.
                       Params:
                               Port number(0-7): 0 = ATOM, 1 = MOCA, 2 = RGMII0, 3 = RGMII1,
                               5 = UDMA0, 6 = UDMA1, 7 = DOCSIS/ARM).
                addPortToVlan        - Adds tagged port to Vlan.
                       Params:
                               Port number(0-7): 0 = ATOM, 1 = MOCA, 2 = RGMII0, 3 = RGMII1,
                               5 = UDMA0, 6 = UDMA1, 7 = DOCSIS/ARM).
                removePortFromVlan   - Removes tagged port from Vlan.
                       Params:
                               Port number(0-7): 0 = ATOM, 1 = MOCA, 2 = RGMII0, 3 = RGMII1,
                               5 = UDMA0, 6 = UDMA1, 7 = DOCSIS/ARM).
                getVlans             - Shows vlan configuration.
                getMcastMacs         - Show static and learned multicast MAC addresses in l2switch.
                getMcastRouterPorts  - Show static and learned multicast MAC addresses in l2switch.
                getUcastMacs         - Show static and learned multicast MAC addresses in l2switch.
                addStaticMac         - Add static MAC address to l2switch fwd table.
                       Params:
                               Ports bitmap: Bitmap value of relevant ports.
                               MACaddress: MAC address to add, format: XX-XX-XX-XX-XX-XX.
                deleteStaticMac      - Delete static MAC address from l2switch fwd table.
                       Params:
                               MACaddress: Static MAC address to delete,
                               format: XX-XX-XX-XX-XX-XX.
                getConfig            - Show current switch configuration..
                getStartupConfig     - Show startup switch configuration..
                getLog               - Get l2switch firmware log.
                enableLog            - Enable firmware logging.
                disableLog           - Disable firmware logging.
                getMachineState      - Get l2switch hardware state.
                enableEgressLogPort  - Enable logging of egressing packets on a port
                       Params:
                               Port number(0-7): 0 = ATOM, 1 = MOCA, 2 = RGMII0, 3 = RGMII1,
                               5 = UDMA0, 6 = UDMA1, 7 = DOCSIS/ARM).
                disableEgressLogPort - Disable logging of egressing packets on a port
                       Params:
                               Port number(0-7): 0 = ATOM, 1 = MOCA, 2 = RGMII0, 3 = RGMII1,
                               5 = UDMA0, 6 = UDMA1, 7 = DOCSIS/ARM).
                enableIngressLogPort - Enable logging of ingressing packets on a port
                       Params:
                               Port number(0-7): 0 = ATOM, 1 = MOCA, 2 = RGMII0, 3 = RGMII1,
                               5 = UDMA0, 6 = UDMA1, 7 = DOCSIS/ARM).
                disableIngressLogPort - Disable logging of ingressing packets on a port
                       Params:
                               Port number(0-7): 0 = ATOM, 1 = MOCA, 2 = RGMII0, 3 = RGMII1,
                               5 = UDMA0, 6 = UDMA1, 7 = DOCSIS/ARM).
                readMDIO             - Perform MDIO read.
                               Params:
                               PhyAddr: PHY address on MDIO bus
                               RegAddr: Register address in PHY.
                writeMDIO            - Perform MDIO write.
                       Params:
                               PhyAddr: PHY address on MDIO bus
                               RegAddr: Register address in PHY
                               Data: Value to write to register.
                readCBUSRegister     - Read CBUS register.
                       Params:
                               RegAddr: CBUS register address.
                writeCBUSRegister    - Write CBUS register.
                       Params:
                               RegAddr: CBUS register address
                               RegVal: Value to write.
                disableIgmpSnooping  - Disables IGMP/MLD snooping in l2switch..
                enableIgmpSnooping   - Enable IGMP/MLD snooping in l2switch..
                dbgGetFwdData        - .
                dbgGetCam            - .
                extswitch            - go to external switch Menu.
                        Init                 - Initialize External Switch           - .
                        Shutdown             - Shutdown External Switch             - .
                        Stats                - Display tx, rx numbers per port      - .
                        addVlanToVtu         - add vlan to VTU                      - <vlanid>.
                        chngPortDefVid       - change the port default VID          - <new default vlanid>, <eth Port(0-5)>.
                        deleteVlan           - delete vlan from VTU                 - <vlanid>.
                        globRdReg            - read glob regs                       - <Global device (0x1b - global 1 registers, 0x1c- global 2 registers)>, <regOffset(0-31)>.
                        globWrReg            - write glob regs                      - <Global device (0x1b - global 1 registers, 0x1c- global 2 registers)>, <regOffset(0-31)>, <vlaue>.
                        getVtuInfo           - get vlan info from VTU               - <vlanid>.
                        initExtSwich         - init extern switch to 802.1q modes   - <802.1q igress mode (0-disable, 1-fallback 2-check 3-secure)>.
                        mapPortToVlan        - map port to vlan                     - <vlanid>, <PortMemberTag (0-untouched, 1-untag 2-tag 3-discard)>, <eth Port(0-internal .. 4)>.
                        removePortFromVlan   - unmap port from vlan                     - <vlanid>, <eth Port(0-5)>.
                        portEnable           - read port params                     - <eth Port(0-internal .. 4)>, <Dis/En (0/1)>.
                        portRdReg            - read port regs                       - <eth Port(0-internal .. 7)>, <regOffset(0-31)>.
                        portWrReg            - write port regs                      - <eth Port(0-internal .. 7)>, <regOffset(0-31)>, <value>.
                        rdAllPortsParams     - read all ports parameters            - .
                        resetSwitch          - reset the switch configuration       - .
                        QinQ_NutralPort      - set port to be a non Q in Q          - <eth Port(0-internal .. 4)>.
                        QinQ_Port            - set port to be a Q in Q              - <eth Port(0-internal .. 4)>, <Q in Q tag type>, <Q in Q vlanid>.
                        show                 - Show external switch configuration.
                        initDB               - init external switch restore DB.
                        restoreSwitch        - restore switch configuration from DB.
                        StatisticsPerPort    - counter statistics per port- <eth Port(0-internal .. 4)>.
                        macAddressTable      - macAddressTable.
                        resetCountersPerPort - reset counters per port<eth Port(0-internal .. 4)>.
                        resetCountersPerAllPorts - reset counters for all ports.
                        phyPortEnable        - enable PHY                           - <eth Port(0-internal .. 4)>, <Dis/En (0/1)>.
                        searchMac            - search mac address                   - MACaddress.
                        addMac               - add mac address                      - MACaddress, <eth Port(0-internal .. 4)>, <Dynamic/Static (0/1)>.
                        delMac               - del mac address                      - MACaddress, <eth Port(0-internal .. 4)>.
                        loopDetectEnable     - enable loop detect function          - <Dis/En (0/1)>.
                        help                 - Display menu commands.
                        shortcuts            - Display key shortcuts help.
                        exit                 - Exit this sub-menu, go to previous menu.
                                                quit                 - Quit and terminate CLI.
                        reboot               - Reboot the system.

                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        arm11_atom_mbx       - Go to Arm11-Atom Mail box Sub-menu.
                sendEvent            - event ID <0x1-0xc0>.
                sendRpcIfEvent       - <APP-CPU IP addr> <NP-CPU IP addr> <Network mask> <VLAN ID>.
                receiveAck           - event ID <0x1-0xc0> .
                sendAck              - event ID <0x1-0xc0> .
                receiveEvent         - event ID <0x1-0xc0> isParamRequiered <0-1> Parameter< 4 bytes> .
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        mmc                  - Go to MMC Controller box Sub-menu.
                show                 - Display settings.
                setcontroller        - <369DB|PS7000|PS8211>, Set MMC controller type.
                imageversion         - Print F/W version in file system.
                fwversion            - Print eMMC Controller F/W version.
                autoupgrade          - <enable|disable>, Enable/Disable auto upgrade on system boot.
                upgrade              - Perform eMMC Controller F/W upgrade.
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        psm                  - Go to PSM sub menu.
                power                - Simulate power <on/off>.
                showMask             - Show power control mask.
                setMask              - Set power control mask <mask | ALL | ALWAYS> <1/0 | 0x*** | 1/0>.
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        lpcm                 - Go to LPCM sub menu.
                enable               - Enable low power consumption feature - reset is required..
                disable              - Disable low power consumption feature - reset is required..
                forced               - Forced low power consumption when CMTS not support EM feature..
                unforced             - Unforced low power consumption when CMTS not support EM feature..
                narrowenable         - Enable narrow scanning mode..
                narrowdisable        - Disable narrow scanning mode, halt and resume wide scanning.
                widetimerset         - Set a timer for wide scanning (in seconds).
                widetimerget         - Get a timer for wide scanning (in seconds).
                widetimerenable      - Enable wide scanning timer.
                widetimerdisable     - Disable wide scanning timer.
                halttimerset         - Set a timer for halt scanning (in seconds).
                halttimerget         - Get a timer for halt scanning (in seconds).
                resumetimerset       - Set a timer for resume scanning (in seconds).
                resumetimerget       - Get a timer for resume scanning (in seconds).
                show details         - Display all LPCM details.
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        network              - Dump networking related information.
        memory               - Dump memory related information.
        timers               - List all GPTimer requests in the system.
        gimdb                - dump the Gim Database on the screen.
        netrxReduce          - Reduce net-rx task priority.
        netrxRestore         - Restore net-rx task priority.
        ipPrint              - Print IP addresses used in the system.
        link                 - Generate LinkUp/Down events : {wlan | moca} {up | down}.
        ProductionSystem     - Go to Production Sub-menu.
                prodset              - Set production params.
                prodshow             - Show production parameters.
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        help                 - Display menu commands.
        shortcuts            - Display key shortcuts help.
        exit                 - Exit this sub-menu, go to previous menu.
                quit                 - Quit and terminate CLI.
        reboot               - Reboot the system.

voice                - Go to Voice Menu.
logger               - Go to Logger Menu.
        ComponentConfig      - set/unset a component (component_id, 1/0).
        AllComponentsConfig  - set/unset all components (1/0).
        ModuleConfig         - set/unset a module (component_id, module_id, 1/0).
        AllModulesConfig     - set/unset all modules (component_id, 1/0).
        SeverityConfig       - set/unset a severity level (severity_level, 1/0).
        AllSeveritiesConfig  - set/unset all severity levels (1/0).
        SocketConfig         - Set the socket of the Logger UDP target (ip_address, port).
        FilenameConfig       - Set the filename for the file target (/dev/pts/0 for telnet).
        QueueLimitConfig     - Set the message queue limits (Message limit, Bytes limit) (0=Unlimited, -1=Default).
        DebugModulesConfig   - Enable/disable debug output of a module (component_id, module_id, 1/0).
        AllDebugModulesConfig - Enable/disable debug output of all modules (component_id, 1/0).
        TimeDisplay          - Set/unset time display  (1/0).
        ComponentDisplay     - Set/unset component display (1/0).
        ModuleDisplay        - Set/unset module display (1/0).
        FullDisplay          - Set full display.
        DefaultDisplay       - Set default display.
        ShortDisplay         - Set short display.
        UserDisplay          - Save/Restore user defined display (1/0).
        TargetConfig         - Set/unset output target (target_id, 1/0).
        componentsList       - Show components list and indicates set/unset for each.
        modulesList          - Show moudles list for a given component (component_id), and indicates set/unset for each.
        severitiesList       - Show severities list and indicates set/unset for each.
        displayConfigList    - Show display config list and indicates set/unset for each.
        targetsList          - Show targets list and indicates set/unset for each.
        socketShow           - Show the socket of the Logger udp target.
        filenameShow         - Show the filaname for file target.
        queueLimitShow       - Show the Logger queue limit.
        setDefaults          - Set Logger's Configuration default valus.
        list                 - Show all components and their modules.
        info                 - Show all logger information (severities, targets, queue...).
        enable               - Enable logger output.
        disable              - Disable logger output.
        help                 - Display menu commands.
        shortcuts            - Display key shortcuts help.
        exit                 - Exit this sub-menu, go to previous menu.
                quit                 - Quit and terminate CLI.
        reboot               - Reboot the system.

eventm               - Go to Event Manager Menu.
        SendEvent            - Send an event through the system (cm/mta, event_number, vendor, must_text, vendor_text).
        SendStdTrap          - Send a standard trap through the system (cm/mta, sub_type, if_id, admin_status, oper_status).
        ResetLog             - Reset the Event Manager's Log (cm/mta).
        DefaultEventTables   - Set the Event Manager tables to default (cm/mta).
        SetEventLevel        - Set new level for an event      (cm/mta, event_id, new_evel).
        SetEventMask         - Set new mask for an event       (cm/mta, event_id, new_mask).
        SetEventText         - Set new text for an event  (cm/mta, event_id, new_text).
        SetPriorityMask      - Set new mask for a priority  (cm/mta, priority, new_mask).
        GetEventsList        - Gets and prints the events list (cm/mta, vendor_events(1/0)).
        SetThrotAdmin        - Set the throttling admin status  (cm/mta, 1-Unconstrained/2-Throt below threshold/3-Throt stop at threshold/4-Inhibited).
        SetThrotThresh       - Set the throttling threshold  (cm/mta, threshold).
        SetThrotInterval     - Set the throttling interval  (cm/mta, interval).
        GetThrotParams       - Get the throttling parameters  (cm/mta).
        StartSyslog          - Start the Syslog service (cm/mta, ipVer: 0-V4/1-V6, IP address).
        StopSyslog           - Stop the Syslog service (cm/mta).
        GetSyslogServer      - Get the Syslog server (cm/mta).
        StartSNMP            - Start the SNMP service (cm/mta).
        StopSNMP             - Stop the SNMP service (cm/mta).
        ExitManager          - Stop and exit from the event manager  (cm/mta).
        help                 - Display menu commands.
        shortcuts            - Display key shortcuts help.
        exit                 - Exit this sub-menu, go to previous menu.
                quit                 - Quit and terminate CLI.
        reboot               - Reboot the system.

version              - prints system version.
pacm                 - Go to PACM Menu.
        version              - prints PACM version.
        options              - prints PACM compilation options.
        provisioning         - go to Provisioning Menu.
                provDebug            - go to Provision Debug Sub-Menu.
                        display_SME_EventsTable - Display the SME events table.
                        help                 - Display menu commands.
                        shortcuts            - Display key shortcuts help.
                        exit                 - Exit this sub-menu, go to previous menu.
                                                quit                 - Quit and terminate CLI.
                        reboot               - Reboot the system.

                dhcpServersConfig    - Set IPv4 addresses of primary and secondary DHCP servers (dotted notation)
                        dhcpServersConfig <primary> <secondary>.
                sendCMLinkUpEvent    - sending CM link up event for starting MTA provisioning.
                sendMSMStartEvent    - sending MSM start event.
                sendDHCPLeaseFailEvent - sending DHCP Lease Fail event.
                sendDHCPNewIPEvent   - sending DHCP New IP event.
                sendCMLinkDownEvent  - sending CM Link Down event <is this T4>.
                sendCMFullScanNoQam  - sending CM Full scan no QAM.
                sendCMQamRegained    - sending CM QAM Regained.
                sendCMResetEvent     - sending CM Reset event.
                sendMTAResetEvent    - sending MTA Reset event.
                sendVoiceRstDoneEvent - sending voice reset done event.
                sendVoiceRstFailEvent - sending voice reset fail event.
                sendSecRstDoneEvent  - sending Sec Reset done event.
                sendSecRstFailEvent  - sending Sec Reset fail event.
                configFile           - Set configuration file URL: <server> <filename>,
                        <server> can't be NULL.
                hashBypassSet        - Set hash checking bypass.
                provDBcontents       - Print contents of provisioning DB.
                setVoiceLoopVoltage  - Changes the loop voltage state.
                tftpAlwaysOn         - Set permanent TFTP download status.
                provStatus           - print the MTA provisioning status.
                provFlow             - Get the MTA provisioning flow.
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        security             - go to Security Menu.
                certificates         - go to Certificates Sub-Menu.
                        getMtaCert           - Get mta certfiles from server tftp <1 for Euro, 0 for NA> <cert> <key> <server ip> .
                        getAllCerts          - Get all the certfiles from server tftp <1 for Euro, 0 for NA> <mtaCert> <mtaKey> <manufacturerCert> <rootCert> <server ip> .
                        certMtaSet           - Set mta certfiles <1 for Euro, 0 for NA> <cert> <key> .
                        certManufSet         - Set manuf certfile <1 for Euro, 0 for NA> <cert>  .
                        certIpteleSet        - Set iptel root certfile <1 for Euro, 0 for NA> <cert>  .
                        resetCertsToDefault  - Reset the certificates of manufacturer and iptel root to default (by nvram flag).
                        setCertRootType      - Set iptel root certificate type <zone: (1)Euro, (0)NA> <root cert type: (1)TestRoot (2)RealRoot>.
                        displayCertsDir      - Display Certs data.
                        displayCertContent   - Display certificate content <zone: (1)Euro, (0)NA> <cert type: (1)MTA (2)Manufacture (3)Root>.
                        help                 - Display menu commands.
                        shortcuts            - Display key shortcuts help.
                        exit                 - Exit this sub-menu, go to previous menu.
                                                quit                 - Quit and terminate CLI.
                        reboot               - Reboot the system.

                resetTickets         - Delete ticket from NVRAM <option> (1)PROV-SERVER (2)CMS (3)ALL.
                overrideCmsTtl       - Override the CMS TTL with this value <value in sec>.
                timersDisplay        - Display Security timers.
                smDataDisplay        - Display state machine data.
                mtaDisplay           - Display current MTA data.
                displayDB            - Print contents of security DB.
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        vendorSubMenu        - go to VendorSubMenu.
                vendorSetDhcpServerAddr - Set the MTA primary DHCP Server Address <IP Address>.
                vendorModifyDhcpAckParam - Modify parameters received in MTA DHCP ACK parameters:
        <flow: 0-Basic 1-Hybrid 2-Secure>
        <MTA24 - syslog 0-false 1-true>
        <MTA25 - Inform 0-false 1-true>
        <download config file 0-false 1-true>
        <local config file name - string>
        <syslog server IP>
        <Realm name - string>.
                vendorSetTftpData    - Set the MTA TFTP server IP and configuration file name <TFTP IP Address> <file name>.
                vendorAddSnmpTarget  - Add a target for sending SNMP message (MTA25) <Server IP Address> <type>.
                printVendorRegisteredEvents - print all vendor registered events.
                VENDOR_STATUS_VENDOR_APP_set - Set status of vendor app <0-disable 1-enable>.
                VENDOR_AFTER_MSM_INIT_set - Set status of VENDOR_AFTER_MSM_INIT message <0-disable 1-enable>.
                VENDOR_SET_DHCP_SERVER_ADDR_set - Set status of VENDOR_SET_DHCP_SERVER_ADDR message <0-disable 1-auto, 2-manual>.
                VENDOR_AFTER_DHCP_ACK_set - Set status of VENDOR_AFTER_DHCP_ACK message <0-disable 1-auto, 2-manual>.
                VENDOR_SET_TFTP_DATA_set - Set status of VENDOR_SET_TFTP_DATA message <0-disable 1-auto, 2-manual>.
                VENDOR_ADD_SNMP_TARGET_set - Set status of VENDOR_ADD_SNMP_TARGET message <0-disable 1-auto, 2-manual>.
                VENDOR_BEFORE_MTA_RESET_set - Set status of VENDOR_BEFORE_MTA_RESET message <0-disable 1-enable>.
                VENDOR_ENABLE_EVENTS_set - Set status of VENDOR_ENABLE_EVENTS message <0-disable 1-enable>.
                VENDOR_ENABLE_DHCP_PLUG_IN_set - Set status of vendor DHCP plug in <0-disable 1-enable>.
                VENDOR_ENABLE_CFM_PLUG_IN_set - Set status of vendor config file manager plug in <0-disable 1-enable>.
                VENDOR_DISABLE_CFM_SPEC_TREE_set - determain spec tree status <0-active (default) 1-disabled>.
                restore              - Restore parameters to defalut.
                save                 - Save all parameters to flash.
                show                 - Print current settings.
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        production           - go to Production Menu.
                prodSet              - Set a parameter by index.
                PACM_CONFIG_EURO_set - Operation mode US/Euro.
                PACM_CONFIG_MTA_NUM_LINES_set - Number of lines.
                PACM_CONFIG_IP_ADDR_set - Configure IP Address.
                PACM_CONFIG_HW_ADDR_set - MTA network device H/W Address.
                PACM_CONFIG_MTA_TELE_ID_set - MTA Slic Type.
                PACM_CONFIG_MTA_BBU_set - MTA BBU Setting.
                PACM_CONFIG_MTA_NUM_SLIC_set - Number of SLIC.
                save                 - Save all parameters to flash.
                show                 - Print current settings.
                setDefaultMacAddress - Set the default MAC-Address to the MTA.
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        dynamicConfig        - go to Dynamic Configuraion Menu.
                set                  - Set a parameter by index.
                PACM_DYN_CONFIG_LOOPV_POLICY_set - Set loop voltage policy.
                PACM_DYN_CONFIG_LOOPV_STATUS_set - Set loop voltage status.
                PACM_DYN_CONFIG_LOOPV_RESET_TIMER_set - Set loop voltage reset timer value.
                PACM_DYN_CONFIG_LOOPV_MAINT_TIMER_CD_set - Set loop voltage maint timer count down value.
                PACM_DYN_CONFIG_SNMP_ENGIN_BOOT_NUM_set - Holds the number of SNMP engine reboots.
                restore              - Restore parameters to defalut.
                save                 - Save all parameters to flash.
                show                 - Print current settings.
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        event                - go to Event Menu.
                sendEvent            - Send an event <eventID> <vendorEvent>.  vendorEvent: (0)False (1)True .
                displayEventTable    - Display the event table.
                printLogFile         - Print the log file to the screen in a formatted manner.
                resetLogFile         - Reset the log file.
                deleteLogFile        - Delete the log file.
                resetTables          - Reset Tables.
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        debugMenu            - go to debugMenu.
                debugSet             - Set a parameter by index.
                PACM_CONFIG_TICKETS_FLASH_SUPPORT_set - Tickets support.
                PACM_CONFIG_PROV_DHCP_RETRIES_set - DHCP Retries during provisioning.
                PACM_CONFIG_IPSEC_ENABLE_set - Enable/Disable IPSEC on board ('False' overrides conf file).
                PACM_CONFIG_PROVISION_FLOWS_SUPPORT_set - Provision flows: bit mask of 0x1=sec; 0x2=hybrid; 0x4=basic.
                PACM_CONFIG_CERTIFICATION_MODE_set - Enable/Disable Certification mode.
                PACM_CONFIG_SNMPV2_ACCESS_set - Enable MTA SNMPv2 access.
                PACM_CONFIG_TLV38_SNMPV1_ENABLE_set - Enable MTA TLV38 SNMPv1 Trap send.
                PACM_CONFIG_CFM_FILE_HASH_BYPASS_set - Enable config file hash checking bypass.
                PACM_CONFIG_MAS_ROUTE_TO_LOGGER_set - Should MAS Spy messages be routed to logger.
                ARRIS_PROVISIONING_set - Arris provisioning type BASIC1=0, BASIC2=1, HYBRID1=2, HYBRID2=3, SECURE=4, GUPI=5, MINUS_KDC=6.
                PACM_CONFIG_EURO_HASH_SIZE_20_set - Enable Euro Hash of size 20.
                PACM_CONFIG_MTA_RESET_WATCH_DOG_set - Enable MTA reset when voice do not answer on cleanup.
                PACM_CONFIG_SEND_CONN_ERROR_EVENT_set - Enable/Disable sending Connection Error event.
                PACM_CONFIG_LOG_PRIORETY_ALGORITHM_set - Enable/Disable writing to local log according to priorety.
                restore              - Restore parameters to defalut.
                save                 - Save all parameters to flash.
                show                 - Print current settings.
                voicePortsSet        - Set voice ports (ports...).
                voicePortsGet        - Print voice ports to the console.
                voiceDropPortsSet    - Set voice drop ports <src> <dst>.
                voiceDropPortsGet    - Print voice drop ports to the console.
                dhcpActive           - Set DHCP status <1-active, 0-not active>.
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        managerMenu          - go to managerMenu.
                PACM_MANAGER_TOD_DELAY_SEC_PROV_set - Set TOD feature status.
                PACM_MANAGER_HITLESS_SOFTWARE_DOWNLOAD_set - Set hitless software download feature status.
                PACM_MANAGER_HITLESS_DHCP_set - Set hitless DHCP feature status.
                PACM_MANAGER_RANDOM_USM_SPIN_LOCK_set - Set random usm spin lock feature status.
                PACM_MANAGER_VENDOR_COMMUNITY_NAME_set - Set specific vendor community name feature status.
                PACM_MANAGER_VENDOR_CMS_AS_IP_set - Set Enable using CMS as IP flag..
                PACM_MANAGER_VENDOR_ENABLE_EVENTS_set - Set status of VENDOR_ENABLE_EVENTS message <0-disable 1-enable>.
                PACM_MANAGER_VOICE_SLIC_PSM_STATUS_set - Set status of Voice PSM features <0-disable 1-enable>.
                PACM_MANAGER_VOICE_DECT_IF_set - Set DECT interface <0-disable 1-enable>.
                PACM_MANAGER_VOICE_VLM_IF_set - Set Enable VLM interfaces <0-disable 1-enable>.
                PACM_MANAGER_SNMP_RESTRICT_CONFIG_VIEW_set - Restrict @mtaconfig view acoording to supported zone.
                PACM_MANAGER_VOICE_SLIC_WB_STATUS_set - Set status of Voice SLIC WB features <0-disable 1-enable>.
                PACM_MANAGER_BBU_ISR_MASK_set - BBU interrupt configuration.
                PACM_MANAGER_VOICE_PP_SUPPORT_set - Set Voice PP Support <0-disable 1-enable>.
                PACM_MANAGER_VOICE_DECT_RST_CTS_SUPPORT_set - Set DECT RTS CTS Support <0-disable 1-enable>.
                restore              - Restore parameters to defalut.
                save                 - Save all parameters to flash.
                show                 - Print current settings.
                help                 - Display menu commands.
                shortcuts            - Display key shortcuts help.
                exit                 - Exit this sub-menu, go to previous menu.
                                quit                 - Quit and terminate CLI.
                reboot               - Reboot the system.

        help                 - Display menu commands.
        shortcuts            - Display key shortcuts help.
        exit                 - Exit this sub-menu, go to previous menu.
                quit                 - Quit and terminate CLI.
        reboot               - Reboot the system.

help                 - Display menu commands.
shortcuts            - Display key shortcuts help.
exit                 - Exit this sub-menu, go to previous menu.
quit                 - Quit and terminate CLI.
reboot               - Reboot the system.
Reply


Messages In This Thread
Arris TG2492 (VM Super hub 3) - by emantec - 07-09-2018, 08:32 PM
RE: Arris TG2492 (VM Super hub 3) - by ricktendo - 08-09-2018, 02:19 PM
RE: Arris TG2492 (VM Super hub 3) - by emantec - 08-09-2018, 02:21 PM
RE: Arris TG2492 (VM Super hub 3) - by drewmerc - 09-09-2018, 05:59 PM
RE: Arris TG2492 (VM Super hub 3) - by emantec - 09-09-2018, 06:10 PM
RE: Arris TG2492 (VM Super hub 3) - by ricktendo - 09-09-2018, 08:20 PM
RE: Arris TG2492 (VM Super hub 3) - by emantec - 09-09-2018, 08:33 PM
RE: Arris TG2492 (VM Super hub 3) - by emantec - 02-11-2018, 11:59 AM
RE: Arris TG2492 (VM Super hub 3) - by andy m - 03-11-2018, 09:27 AM
RE: Arris TG2492 (VM Super hub 3) - by vmu19 - 18-01-2019, 10:32 AM
RE: Arris TG2492 (VM Super hub 3) - by andy m - 18-01-2019, 08:28 PM
RE: Arris TG2492 (VM Super hub 3) - by vmu19 - 18-01-2019, 08:41 PM
RE: Arris TG2492 (VM Super hub 3) - by andy m - 19-01-2019, 10:25 AM
RE: Arris TG2492 (VM Super hub 3) - by vmu19 - 19-01-2019, 01:05 PM
RE: Arris TG2492 (VM Super hub 3) - by andy m - 19-01-2019, 06:30 PM
RE: Arris TG2492 (VM Super hub 3) - by vmu19 - 19-01-2019, 07:46 PM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 20-01-2019, 03:20 AM
RE: Arris TG2492 (VM Super hub 3) - by vmu19 - 20-01-2019, 10:12 AM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 20-01-2019, 03:48 PM
RE: Arris TG2492 (VM Super hub 3) - by vmu19 - 20-01-2019, 04:50 PM
RE: Arris TG2492 (VM Super hub 3) - by danman - 25-02-2019, 10:49 AM
RE: Arris TG2492 (VM Super hub 3) - by elbarto - 26-03-2019, 12:47 AM
RE: Arris TG2492 (VM Super hub 3) - by danman - 25-02-2019, 10:53 AM
RE: Arris TG2492 (VM Super hub 3) - by danman - 25-02-2019, 11:46 AM
RE: Arris TG2492 (VM Super hub 3) - by danman - 02-03-2019, 12:06 PM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 02-03-2019, 02:10 PM
RE: Arris TG2492 (VM Super hub 3) - by danman - 02-03-2019, 05:24 PM
RE: Arris TG2492 (VM Super hub 3) - by guti - 19-04-2019, 09:25 PM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 28-04-2019, 10:55 PM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 02-03-2019, 11:29 PM
RE: Arris TG2492 (VM Super hub 3) - by danman - 03-03-2019, 12:00 AM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 03-03-2019, 12:02 AM
RE: Arris TG2492 (VM Super hub 3) - by danman - 03-03-2019, 12:09 AM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 03-03-2019, 12:27 AM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 03-03-2019, 12:08 AM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 03-03-2019, 12:32 AM
RE: Arris TG2492 (VM Super hub 3) - by danman - 03-03-2019, 12:37 AM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 03-03-2019, 12:44 AM
RE: Arris TG2492 (VM Super hub 3) - by danman - 03-03-2019, 12:47 AM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 03-03-2019, 12:39 AM
RE: Arris TG2492 (VM Super hub 3) - by danman - 03-03-2019, 12:43 AM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 03-03-2019, 12:49 AM
RE: Arris TG2492 (VM Super hub 3) - by danman - 03-03-2019, 01:06 AM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 03-03-2019, 01:09 AM
RE: Arris TG2492 (VM Super hub 3) - by danman - 03-03-2019, 01:13 AM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 03-03-2019, 01:22 AM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 03-03-2019, 10:44 PM
RE: Arris TG2492 (VM Super hub 3) - by danman - 03-03-2019, 11:00 PM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 03-03-2019, 11:06 PM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 06-03-2019, 05:42 AM
RE: Arris TG2492 (VM Super hub 3) - by danman - 06-03-2019, 07:10 PM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 16-03-2019, 07:24 PM
RE: Arris TG2492 (VM Super hub 3) - by 0xff - 03-03-2019, 03:39 AM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 03-03-2019, 04:06 AM
RE: Arris TG2492 (VM Super hub 3) - by 0xff - 03-03-2019, 04:19 AM
RE: Arris TG2492 (VM Super hub 3) - by emantec - 09-04-2019, 04:30 PM
RE: Arris TG2492 (VM Super hub 3) - by ricktendo - 12-04-2019, 06:11 AM
RE: Arris TG2492 (VM Super hub 3) - by emantec - 12-04-2019, 07:27 PM
RE: Arris TG2492 (VM Super hub 3) - by ricktendo - 14-04-2019, 06:25 PM
RE: Arris TG2492 (VM Super hub 3) - by andy m - 14-04-2019, 07:12 PM
RE: Arris TG2492 (VM Super hub 3) - by ricktendo - 14-04-2019, 08:41 PM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 16-04-2019, 09:33 AM
RE: Arris TG2492 (VM Super hub 3) - by emantec - 16-04-2019, 12:07 PM
RE: Arris TG2492 (VM Super hub 3) - by elbarto - 21-04-2019, 03:43 PM
RE: Arris TG2492 (VM Super hub 3) - by emantec - 16-04-2019, 09:52 PM
RE: Arris TG2492 (VM Super hub 3) - by elbarto - 17-04-2019, 04:43 PM
RE: Arris TG2492 (VM Super hub 3) - by emantec - 19-04-2019, 10:32 AM
RE: Arris TG2492 (VM Super hub 3) - by emantec - 21-04-2019, 12:59 PM
RE: Arris TG2492 (VM Super hub 3) - by emantec - 22-04-2019, 08:08 PM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 29-04-2019, 02:37 AM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 30-06-2019, 09:59 PM
RE: Arris TG2492 (VM Super hub 3) - by ricktendo - 29-04-2019, 06:23 AM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 29-04-2019, 06:29 AM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 29-04-2019, 10:22 PM
RE: Arris TG2492 (VM Super hub 3) - by neo_ - 14-06-2019, 12:37 AM
RE: Arris TG2492 (VM Super hub 3) - by ricktendo - 14-06-2019, 02:03 AM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 02-07-2019, 06:36 AM
RE: Arris TG2492 (VM Super hub 3) - by danman - 15-07-2019, 03:14 PM
RE: Arris TG2492 (VM Super hub 3) - by eltremendo - 16-07-2019, 05:04 AM
RE: Arris TG2492 (VM Super hub 3) - by danman - 16-07-2019, 06:43 AM
RE: Arris TG2492 (VM Super hub 3) - by smoker - 07-08-2019, 10:18 PM
RE: Arris TG2492 (VM Super hub 3) - by andy m - 08-08-2019, 09:56 AM
RE: Arris TG2492 (VM Super hub 3) - by sb5101e - 04-01-2020, 01:07 PM
RE: Arris TG2492 (VM Super hub 3) - by jorgitolmj - 06-04-2021, 08:42 AM
RE: Arris TG2492 (VM Super hub 3) - by alvaro1970 - 26-01-2020, 11:04 PM
RE: Arris TG2492 (VM Super hub 3) - by kapec - 10-04-2020, 09:01 AM
RE: Arris TG2492 (VM Super hub 3) - by travis1999 - 05-04-2021, 12:15 AM
RE: Arris TG2492 (VM Super hub 3) - by alexlobo - 15-07-2021, 04:57 AM
RE: Arris TG2492 (VM Super hub 3) - by infinity08 - 26-07-2021, 06:02 AM

Forum Jump:


Users browsing this thread: 3 Guest(s)