Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Need to know where to drop the keys certs and configure files on dragon
#1
I added Dragon to a working forceware 6121 modem but I don’t know where to drop the keys Certs and config files
Or what to name the files
Reply
#2
CHANGE OF CERTIFICATES Rename the komodo firmware certificate as cm_cert.cer and your private key as cm_key_prv.bin
With WinSCP or some stfp client, transfer them to /nvram/1/security
Reply
#3
(31-03-2020, 12:26 PM)BPSX Wrote: I added Dragon to a working forceware 6121 modem but I don’t know where to drop the keys Certs and config files
Or what to name the files

anyway you can share me the dragon software ?
Reply
#4
I'm having trouble logging in...the 192 does not work for me. Any advice?
Reply
#5
Same I flash firmware and I cannot enter ip.
Reply
#6
(01-05-2020, 07:10 AM)MikeHoncho Wrote: I'm having trouble logging in...the 192 does not work for me. Any advice?
try changing nic address to 192.168.100.2 you should be able to get into GUI

Reply
#7
(03-05-2020, 03:22 AM)doctor Wrote:
(01-05-2020, 07:10 AM)MikeHoncho Wrote: I'm having trouble logging in...the 192 does not work for me. Any advice?
try changing nic address to 192.168.100.2 you should be able to get into GUI

Please any advice how to do that in windows?
Reply
#8
(03-05-2020, 10:27 PM)ramses18 Wrote:
(03-05-2020, 03:22 AM)doctor Wrote:
(01-05-2020, 07:10 AM)MikeHoncho Wrote: I'm having trouble logging in...the 192 does not work for me. Any advice?
try changing nic address to 192.168.100.2 you should be able to get into GUI

Please any advice how to do that in windows?

you have to change manually ipv4
IP address 192.168.100.10
subnet       225.255.255.0
Default       192.168.100.1
Reply
#9
(03-05-2020, 10:59 PM)Mike323 Wrote:
(03-05-2020, 10:27 PM)ramses18 Wrote:
(03-05-2020, 03:22 AM)doctor Wrote:
(01-05-2020, 07:10 AM)MikeHoncho Wrote: I'm having trouble logging in...the 192 does not work for me. Any advice?
try changing nic address to 192.168.100.2 you should be able to get into GUI

Please any advice how to do that in windows?

you have to change manually ipv4
IP address 192.168.100.10
subnet       225.255.255.0
Default       192.168.100.1
Thanks I will try it.
Reply
#10
(04-05-2020, 01:51 AM)ramses18 Wrote:
(03-05-2020, 10:59 PM)Mike323 Wrote:
(03-05-2020, 10:27 PM)ramses18 Wrote:
(03-05-2020, 03:22 AM)doctor Wrote:
(01-05-2020, 07:10 AM)MikeHoncho Wrote: I'm having trouble logging in...the 192 does not work for me. Any advice?
try changing nic address to 192.168.100.2 you should be able to get into GUI

Please any advice how to do that in windows?

you have to change manually ipv4
IP address 192.168.100.10
subnet       225.255.255.0
Default       192.168.100.1
Thanks I will try it.

Did you get config forcing to work? Didn't work for me on rev8 mod1 and mod6. Modem online but very slow speeds due to no config forcing. Tried two sets of cert/config both behaved that way
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)