10-11-2012, 11:59 PM
Fix. So here is the event log: http://pastebin.com/jx80n1T5 and here is the subsequent telnet log from the same time period: http://pastebin.com/YUgT2wQr. For those too impatient to load a page, i have attached the telnet log to the bottom of this post.
Thanks for the help!
gbradm
*******************************************************
Transcript from Android Terminal Emulator
Brad <george.@gmail.com> Sat, Nov 10, 2012 at 6:25 PM
To: George Bradley <george.@gmail.com>
u0_a64@android:/ $ telnet 192.168.1.117
Entering character mode
Escape character is '^]'.
Haxorware integrated telnet daemon
Username: root
Password: ********
Welcome.
Attempting Downstream FEC lock @ freq= 613750000 Hz, QAM64
CM>
Error - Unknown command: ''
CM> Attempting Downstream FEC lock @ freq= 619750000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 625750000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 631750000 Hz, QAM64
Favorite[0].freq = 681000000
Attempting Downstream FEC lock @ freq= 681000000 Hz, QAM64/256
Go back to 1st favorite
Attempting Downstream FEC lock @ freq= 115750000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 493750000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 127750000 Hz, QAM64
Favorite[0].freq = 681000000
Attempting Downstream FEC lock @ freq= 681000000 Hz, QAM64/256
Go back to 1st favorite
Attempting Downstream FEC lock @ freq= 121750000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 499750000 Hz, QAM256
*********************************
********* *********
********* EDITED *********
********* *********
*********************************
Attempting Downstream FEC lock @ freq= 505750000 Hz, QAM256
Attempting Downstream FEC lock @ freq= 337750000 Hz, QAM256
Found energy at frequency 337750000Hz! Publishing event kEventEnergyDetected...
Attempting Downstream FEC lock @ freq= 331750000 Hz, QAM256
Attempting Downstream FEC lock @ freq= 325750000 Hz, QAM256
Attempting Downstream FEC lock @ freq= 139750000 Hz, QAM256
Favorite[0].freq = 681000000
Attempting Downstream FEC lock @ freq= 681000000 Hz, QAM64/256
0x00721dc0 [CmDocsisCtlThread] BcmCmDocsisCtlThread::StartUsInit: (CmDocsisCtlThread) Locked on the downstream. Waiting for UCDs...
******************************************
DOWNSTREAM STATUS
******************************************
Tuner Frequency = 681000000 Hz
Carrier Offset = -1 Hz
Symbol rate = 5360537 sym/sec
SNR = 37 dB
QAM Mode = QAM256
Tuner AGC = 0xfff00000
IF AGC = 0x136311eb
Power Level = 5 dB
QAM = LOCKED
FEC = LOCKED
******************************************
Calculating maximum number of IP filters:
Each IP filter consumes 1856 bytes of RAM.
Current free RAM is 246932 bytes.
Max heap reserved for IP filters (25%) = 61733
We can support 33 IP filters.
Calculating maximum number of LLC filters:
Each LLC filter consumes 724 bytes of RAM.
Current free RAM is 246932 bytes.
Max heap reserved for LLC filters (25%) = 61733
We can support 85 LLC filters.
CM> Selecting UCD for Us Channel 2
0x00722626 [CmDocsisCtlThread] BcmCmDocsisCtlThread::TestAndLaunchDsTimeSync: (CmDocsisCtlThread) starting ds time sync acquisition...
0x007228c4 [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncDsSyncOk: (CmDocsisCtlThread) downstream time sync acquired...
0x007228c4 [CmDocsisCtlThread] BcmCmDocsisCtlThread::DsSyncOkResumeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial ranging.
Beginning initial ranging...
Using stored initial upstream power = 41.0 dBmV
0x007228ce [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncDsSyncOk: (CmDocsisCtlThread) rx unexpected kDsSyncOk indication...
Logging event: Acquired Downstream (681000000 Hz)........ SUCCESS
RNG-RSP Adj: tim=4000 power=-6 freq=0 Stat=Continue
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Continue
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Continue
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Continue
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Success
******************************************
UPSTREAM STATUS
******************************************
Upstream Status = UP
Upstream Channel = 2
Upstream Frequency = 28200000 Hz
Upstream Power = 40 dBmV
Ranging SID = 0x57f
Upstream Symbol Rate = 5120000 sym/sec
******************************************
Starting IP Initialization with DHCP...
DHCPc: Waiting 1 seconds before sending Discover; client id htype=1, value=00:11:e3:c6:d5:db
Logging event: Acquired Upstream .......... SUCCESS
CM> DHCPc: Sending Discover packet; client id htype=1, value=00:11:e3:c6:d5:db
DHCPc: Received an Offer from DHCP server c4:71:fe:76:98:e2 (96.70.158.1); lease client id htype=1, value=00:11:e3:c6:d5:db
CM> DHCPc: Timed out waiting for offers for lease with client id htype=1, value=00:11:e3:c6:d5:db
DHCPc: Sending Request packet; client id htype=1, value=00:11:e3:c6:d5:db
DHCPc: Received an Ack from DHCP server c4:71:fe:76:98:e2 (96.70.158.1); lease client id htype=1, value=00:11:e3:c6:d5:db
Current IP address is default 0.0.0.0.
0x00724502 [DHCP Client Thread] BcmEcosIpHalIf::ConfigureLeaseImpl: (IP Stack1 HalIf)
Configuring IP stack 1:
IP Address = 73.13.183.182 (primary IP address)
Subnet Mask = 255.255.254.0
Router = 73.13.182.1
IsPrimaryInterface = 1
Logging event: DHCP WARNING - Non-critical field invalid in response.
ARPing for default GW IP = 73.13.182.1
MAC = c4:71:fe:76:98:e2
DHCP completed successfully!
DHCP Settings:
Client Id = htype=1, value=00:11:e3:c6:d5:db
State = Renewing (5)
Static Lease = 0
AutoConfig Mode = IP, Subnet and Router
XID = 0x675b7106
Number of Tries = 0
Max Discover Tries = 6
Max Request Tries = 6
DHCP server MAC addr = c4:71:fe:76:98:e2
Ignore NAKs = 0
My offered IP address = 73.13.183.182 (primary IP address)
(1) Subnet Mask = 255.255.254.0
(3) Router IP address = 73.13.182.1
(54) DHCP Server IP address = 69.252.196.132
(82) Relay Agent IP address = 96.70.158.1
TFTP Server IP address = 68.86.58.223
CM Configuration file = 'd11_m_dcm425_silver_c01.cm'
(2) UTC Time Offset = -18000 seconds
(4) Time Server IP address = 69.252.196.198
(6) Domain Name Server = 68.87.68.162; 68.87.74.162
(7) Log Server IP address = 0.0.0.0
(51) Lease time = 503770 seconds
(58) T1 (renew) = 251885 seconds
(59) T2 (rebind) = 440798 seconds
Lease is infinite = 0
SB5102 CM Agent w/ BRCM Factory Support IpStackEvent: Ip=73.13.183.182, Subnet=255.255.254.0, Gateway=73.13.182.1
CmSnmpAgent::IpAddressAcquiredEvent for SB5102 CM Agent w/ BRCM Factory Support
IP addr = 73.13.183.182
Starting Time Of Day...
0x007245a2 [CmDocsisIpThread] BcmDocsisTimeOfDayThread::SetTodServerIpAddress: (Time Of Day Thread) ToD servers: 69.252.196.198
Connecting to ToD server 69.252.196.198...
Sending UDP ToD request to server...
SNMP Agent Binding to 73.13.183.182:225
Logging event: Retrieved DHCP .......... SUCCESS
CM> UTC returned by ToD server 3561574874; UTC offset -18000
Current system time -> Sat Nov 10 17:21:14 2012
System start time -> Sat Nov 10 15:16:25 2012
Starting Tftp of configuration file...
Opening file 'd11_m_dcm425_silver_c01.cm' on 68.86.58.223 for reading...
tftp-enforce bypass is DISABLED
Storing received cfg of size 4938 to memory
Tftp read < 512 bytes, we have reached end of file.
Tftp transfer complete!
TFTP Settings:
Stack Interface = 1
Server Ip Address = 68.86.58.223
Server Port Number = 69
Total Blocks Read = 10
Total Bytes Read = 4938
Config file was read! IP Initialization completed...
MAX CPE per CM is being set to 32
TLV-11[1]: 1.3.6.1.2.1.69.1.3.3.0 -> 2 (i32)
TLV-11[2]: 1.3.6.1.2.1.69.1.2.1.2.1 -> 68.85.0.0
TLV-11[3]: 1.3.6.1.2.1.69.1.2.1.3.1 -> 255.255.0.0
TLV-11[4]: 1.3.6.1.2.1.69.1.2.1.4.1 -> hDaFHJG7
*********************************
********* *********
********* EDITED *********
********* *********
*********************************
TLV-11[172]: 1.3.6.1.2.1.69.1.6.4.1.15.73 -> 65535 (i32)
Time Of Day completed...
DefaultSnmpAgentClass::SystemTimeChangeEvent for SB5102 CM Agent w/ BRCM Factory Support
Logging event: Retrieved TFTP Config d11_m_dcm425_silver_c01.cm SUCCESS
Logging event: Retrieved Time....... SUCCESS
SB5102 CM Agent w/ BRCM Factory Support processing TLV-11's
SNMP packet sent to 73.13.183.182:225
Insufficient heap to handle SNMP packet - TOO_BIG.
(PDU = 204084, heap = 31372)
TLV-11 failure: error status=1, error index=0
Invalid TLV-11's: 1 wrong values, 0 duplicate sets.
SNMP Error'd but Haxorware doesn't care AT ALL!
Onwards mateys!
Sending a REG-REQ to the CMTS...
Received a REG-RSP message from the CMTS...
0x007251aa [CmDocsisCtlThread] BcmCmDocsisCtlThread::RegRspMsgEvent: (CmDocsisCtlThread) We registered with a DOCSIS 1.1 config file!
Registration complete!
Process CVC
Co-signer CVC verified
At least one CVC is valid.
DOCSIS CoS/QoS rate shaping enable is now 1
CmSnmpAgent::CmOperationalEvent for SB5102 CM Agent w/ BRCM Factory Support
CmSnmpAgent operating in 1.1 mode, including docsQos, excluding docsBpi
+++ No DH kickstart profiles or snmpCommunityTable entries installed.
We will operate in NMACCESS mode.
SB5102 CM Agent w/ BRCM Factory Support setting V1/V2 view to docsisNmAccessView
SB5102 CM Agent w/ BRCM Factory Support enabling management.
SB5102 CM Agent w/ BRCM Factory Support sending deferred traps...
Done w/ deferred traps.
SB5102 CPE Agent w/ BRCM Factory Support setting V1/V2 view to docsisNmAccessView
0x00725204 [CmDocsisCtlThread] BcmCmDocsisCtlThread::TestAndLaunchBpkm: (CmDocsisCtlThread) BPKM disabled via manufacturing setting.
Enabling network access for all CPE ports.
mot_scanList: Writing to Flash!
NonVolDeviceDriver::NonVolDriverWrite: WARNING - Current segment size < buffer size! Increasing the segment size!
BcmCmDocsisStatusEventCodes::kCmIsOperational
Suspending SNMP Thread
0x007254c0 [CmDocsisCtlThread] BcmVendorCmApplication::StopDhcpServer: (VendorExtension CmApp) Shutting down DHCP Server...
0x007254c0 [CmDocsisCtlThread] BcmStandbySwitchThread::CmIsOperational: (Motorola Standby Switch Thread) Simulating a press of the standby switch to get the state configured properly.
0x007254ca [IGMP Thread] BcmIgmpThread::Starting Igmp Thread...: (IGMP Thread)
0x007254d4 [Motorola Standby Switch Thread] BcmStandbySwitchThread::ThreadMain: (Motorola Standby Switch Thread) Standby switch was pressed!
0x007254d4 [Motorola Standby Switch Thread] BcmStandbySwitchThread::ProcessSwitchEvent: (Motorola Standby Switch Thread) Standby switch disabled in nonvol; ignoring event.
Logging event: TLV-11 - Illegal Set operation failed
Sending syslog message from IF 1 to 192.168.1.10:
<130> CABLEMODEM [DOCSIS]: <73040200> TLV-11 - Illegal Set operation failed
SB5102 CM Event Log w/ BRCM Factory Support sending deferred async messages...
Sending syslog message from IF 1 to 192.168.1.10:
<130> CABLEMODEM [DOCSIS]: <84000200> SYNC Timing Synchronization failure - Failed to acquire FEC framing
Sending syslog message from IF 1 to 192.168.1.10:
<133> CABLEMODEM [Motorola Corporation]: <2300955725> Ethernet link up - ready to pass packets
Sending syslog message from IF 1 to 192.168.1.10:
<130> CABLEMODEM [DOCSIS]: <84000100> SYNC Timing Synchronization failure - Failed to acquire QAM/QPSK symbol timing
Sending syslog message from IF 1 to 192.168.1.10:
<130> CABLEMODEM [DOCSIS]: <84000100> SYNC Timing Synchronization failure - Failed to acquire QAM/QPSK symbol timing
Sending syslog message from IF 1 to 192.168.1.10:
<130> CABLEMODEM [DOCSIS]: <84000100> SYNC Timing Synchronization failure - Failed to acquire QAM/QPSK symbol timing
Sending syslog message from IF 1 to 192.168.1.10:
<130> CABLEMODEM [DOCSIS]: <84000100> SYNC Timing Synchronization failure - Failed to acquire QAM/QPSK symbol timing
Sending syslog message from IF 1 to 192.168.1.10:
*********************************
********* *********
********* EDITED *********
********* *********
*********************************
Sending syslog message from IF 1 to 192.168.1.10:
<130> CABLEMODEM [DOCSIS]: <84000100> SYNC Timing Synchronization failure - Failed to acquire QAM/QPSK symbol timing
Sending syslog message from IF 1 to 192.168.1.10:
Thanks for the help!
gbradm
*******************************************************
Transcript from Android Terminal Emulator
Brad <george.@gmail.com> Sat, Nov 10, 2012 at 6:25 PM
To: George Bradley <george.@gmail.com>
u0_a64@android:/ $ telnet 192.168.1.117
Entering character mode
Escape character is '^]'.
Haxorware integrated telnet daemon
Username: root
Password: ********
Welcome.
Attempting Downstream FEC lock @ freq= 613750000 Hz, QAM64
CM>
Error - Unknown command: ''
CM> Attempting Downstream FEC lock @ freq= 619750000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 625750000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 631750000 Hz, QAM64
Favorite[0].freq = 681000000
Attempting Downstream FEC lock @ freq= 681000000 Hz, QAM64/256
Go back to 1st favorite
Attempting Downstream FEC lock @ freq= 115750000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 493750000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 127750000 Hz, QAM64
Favorite[0].freq = 681000000
Attempting Downstream FEC lock @ freq= 681000000 Hz, QAM64/256
Go back to 1st favorite
Attempting Downstream FEC lock @ freq= 121750000 Hz, QAM64
Attempting Downstream FEC lock @ freq= 499750000 Hz, QAM256
*********************************
********* *********
********* EDITED *********
********* *********
*********************************
Attempting Downstream FEC lock @ freq= 505750000 Hz, QAM256
Attempting Downstream FEC lock @ freq= 337750000 Hz, QAM256
Found energy at frequency 337750000Hz! Publishing event kEventEnergyDetected...
Attempting Downstream FEC lock @ freq= 331750000 Hz, QAM256
Attempting Downstream FEC lock @ freq= 325750000 Hz, QAM256
Attempting Downstream FEC lock @ freq= 139750000 Hz, QAM256
Favorite[0].freq = 681000000
Attempting Downstream FEC lock @ freq= 681000000 Hz, QAM64/256
0x00721dc0 [CmDocsisCtlThread] BcmCmDocsisCtlThread::StartUsInit: (CmDocsisCtlThread) Locked on the downstream. Waiting for UCDs...
******************************************
DOWNSTREAM STATUS
******************************************
Tuner Frequency = 681000000 Hz
Carrier Offset = -1 Hz
Symbol rate = 5360537 sym/sec
SNR = 37 dB
QAM Mode = QAM256
Tuner AGC = 0xfff00000
IF AGC = 0x136311eb
Power Level = 5 dB
QAM = LOCKED
FEC = LOCKED
******************************************
Calculating maximum number of IP filters:
Each IP filter consumes 1856 bytes of RAM.
Current free RAM is 246932 bytes.
Max heap reserved for IP filters (25%) = 61733
We can support 33 IP filters.
Calculating maximum number of LLC filters:
Each LLC filter consumes 724 bytes of RAM.
Current free RAM is 246932 bytes.
Max heap reserved for LLC filters (25%) = 61733
We can support 85 LLC filters.
CM> Selecting UCD for Us Channel 2
0x00722626 [CmDocsisCtlThread] BcmCmDocsisCtlThread::TestAndLaunchDsTimeSync: (CmDocsisCtlThread) starting ds time sync acquisition...
0x007228c4 [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncDsSyncOk: (CmDocsisCtlThread) downstream time sync acquired...
0x007228c4 [CmDocsisCtlThread] BcmCmDocsisCtlThread::DsSyncOkResumeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial ranging.
Beginning initial ranging...
Using stored initial upstream power = 41.0 dBmV
0x007228ce [CmDocsisCtlThread] BcmCmDocsisCtlThread::SyncDsSyncOk: (CmDocsisCtlThread) rx unexpected kDsSyncOk indication...
Logging event: Acquired Downstream (681000000 Hz)........ SUCCESS
RNG-RSP Adj: tim=4000 power=-6 freq=0 Stat=Continue
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Continue
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Continue
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Continue
RNG-RSP Adj: tim=0 power=0 freq=0 Stat=Success
******************************************
UPSTREAM STATUS
******************************************
Upstream Status = UP
Upstream Channel = 2
Upstream Frequency = 28200000 Hz
Upstream Power = 40 dBmV
Ranging SID = 0x57f
Upstream Symbol Rate = 5120000 sym/sec
******************************************
Starting IP Initialization with DHCP...
DHCPc: Waiting 1 seconds before sending Discover; client id htype=1, value=00:11:e3:c6:d5:db
Logging event: Acquired Upstream .......... SUCCESS
CM> DHCPc: Sending Discover packet; client id htype=1, value=00:11:e3:c6:d5:db
DHCPc: Received an Offer from DHCP server c4:71:fe:76:98:e2 (96.70.158.1); lease client id htype=1, value=00:11:e3:c6:d5:db
CM> DHCPc: Timed out waiting for offers for lease with client id htype=1, value=00:11:e3:c6:d5:db
DHCPc: Sending Request packet; client id htype=1, value=00:11:e3:c6:d5:db
DHCPc: Received an Ack from DHCP server c4:71:fe:76:98:e2 (96.70.158.1); lease client id htype=1, value=00:11:e3:c6:d5:db
Current IP address is default 0.0.0.0.
0x00724502 [DHCP Client Thread] BcmEcosIpHalIf::ConfigureLeaseImpl: (IP Stack1 HalIf)
Configuring IP stack 1:
IP Address = 73.13.183.182 (primary IP address)
Subnet Mask = 255.255.254.0
Router = 73.13.182.1
IsPrimaryInterface = 1
Logging event: DHCP WARNING - Non-critical field invalid in response.
ARPing for default GW IP = 73.13.182.1
MAC = c4:71:fe:76:98:e2
DHCP completed successfully!
DHCP Settings:
Client Id = htype=1, value=00:11:e3:c6:d5:db
State = Renewing (5)
Static Lease = 0
AutoConfig Mode = IP, Subnet and Router
XID = 0x675b7106
Number of Tries = 0
Max Discover Tries = 6
Max Request Tries = 6
DHCP server MAC addr = c4:71:fe:76:98:e2
Ignore NAKs = 0
My offered IP address = 73.13.183.182 (primary IP address)
(1) Subnet Mask = 255.255.254.0
(3) Router IP address = 73.13.182.1
(54) DHCP Server IP address = 69.252.196.132
(82) Relay Agent IP address = 96.70.158.1
TFTP Server IP address = 68.86.58.223
CM Configuration file = 'd11_m_dcm425_silver_c01.cm'
(2) UTC Time Offset = -18000 seconds
(4) Time Server IP address = 69.252.196.198
(6) Domain Name Server = 68.87.68.162; 68.87.74.162
(7) Log Server IP address = 0.0.0.0
(51) Lease time = 503770 seconds
(58) T1 (renew) = 251885 seconds
(59) T2 (rebind) = 440798 seconds
Lease is infinite = 0
SB5102 CM Agent w/ BRCM Factory Support IpStackEvent: Ip=73.13.183.182, Subnet=255.255.254.0, Gateway=73.13.182.1
CmSnmpAgent::IpAddressAcquiredEvent for SB5102 CM Agent w/ BRCM Factory Support
IP addr = 73.13.183.182
Starting Time Of Day...
0x007245a2 [CmDocsisIpThread] BcmDocsisTimeOfDayThread::SetTodServerIpAddress: (Time Of Day Thread) ToD servers: 69.252.196.198
Connecting to ToD server 69.252.196.198...
Sending UDP ToD request to server...
SNMP Agent Binding to 73.13.183.182:225
Logging event: Retrieved DHCP .......... SUCCESS
CM> UTC returned by ToD server 3561574874; UTC offset -18000
Current system time -> Sat Nov 10 17:21:14 2012
System start time -> Sat Nov 10 15:16:25 2012
Starting Tftp of configuration file...
Opening file 'd11_m_dcm425_silver_c01.cm' on 68.86.58.223 for reading...
tftp-enforce bypass is DISABLED
Storing received cfg of size 4938 to memory
Tftp read < 512 bytes, we have reached end of file.
Tftp transfer complete!
TFTP Settings:
Stack Interface = 1
Server Ip Address = 68.86.58.223
Server Port Number = 69
Total Blocks Read = 10
Total Bytes Read = 4938
Config file was read! IP Initialization completed...
MAX CPE per CM is being set to 32
TLV-11[1]: 1.3.6.1.2.1.69.1.3.3.0 -> 2 (i32)
TLV-11[2]: 1.3.6.1.2.1.69.1.2.1.2.1 -> 68.85.0.0
TLV-11[3]: 1.3.6.1.2.1.69.1.2.1.3.1 -> 255.255.0.0
TLV-11[4]: 1.3.6.1.2.1.69.1.2.1.4.1 -> hDaFHJG7
*********************************
********* *********
********* EDITED *********
********* *********
*********************************
TLV-11[172]: 1.3.6.1.2.1.69.1.6.4.1.15.73 -> 65535 (i32)
Time Of Day completed...
DefaultSnmpAgentClass::SystemTimeChangeEvent for SB5102 CM Agent w/ BRCM Factory Support
Logging event: Retrieved TFTP Config d11_m_dcm425_silver_c01.cm SUCCESS
Logging event: Retrieved Time....... SUCCESS
SB5102 CM Agent w/ BRCM Factory Support processing TLV-11's
SNMP packet sent to 73.13.183.182:225
Insufficient heap to handle SNMP packet - TOO_BIG.
(PDU = 204084, heap = 31372)
TLV-11 failure: error status=1, error index=0
Invalid TLV-11's: 1 wrong values, 0 duplicate sets.
SNMP Error'd but Haxorware doesn't care AT ALL!
Onwards mateys!
Sending a REG-REQ to the CMTS...
Received a REG-RSP message from the CMTS...
0x007251aa [CmDocsisCtlThread] BcmCmDocsisCtlThread::RegRspMsgEvent: (CmDocsisCtlThread) We registered with a DOCSIS 1.1 config file!
Registration complete!
Process CVC
Co-signer CVC verified
At least one CVC is valid.
DOCSIS CoS/QoS rate shaping enable is now 1
CmSnmpAgent::CmOperationalEvent for SB5102 CM Agent w/ BRCM Factory Support
CmSnmpAgent operating in 1.1 mode, including docsQos, excluding docsBpi
+++ No DH kickstart profiles or snmpCommunityTable entries installed.
We will operate in NMACCESS mode.
SB5102 CM Agent w/ BRCM Factory Support setting V1/V2 view to docsisNmAccessView
SB5102 CM Agent w/ BRCM Factory Support enabling management.
SB5102 CM Agent w/ BRCM Factory Support sending deferred traps...
Done w/ deferred traps.
SB5102 CPE Agent w/ BRCM Factory Support setting V1/V2 view to docsisNmAccessView
0x00725204 [CmDocsisCtlThread] BcmCmDocsisCtlThread::TestAndLaunchBpkm: (CmDocsisCtlThread) BPKM disabled via manufacturing setting.
Enabling network access for all CPE ports.
mot_scanList: Writing to Flash!
NonVolDeviceDriver::NonVolDriverWrite: WARNING - Current segment size < buffer size! Increasing the segment size!
BcmCmDocsisStatusEventCodes::kCmIsOperational
Suspending SNMP Thread
0x007254c0 [CmDocsisCtlThread] BcmVendorCmApplication::StopDhcpServer: (VendorExtension CmApp) Shutting down DHCP Server...
0x007254c0 [CmDocsisCtlThread] BcmStandbySwitchThread::CmIsOperational: (Motorola Standby Switch Thread) Simulating a press of the standby switch to get the state configured properly.
0x007254ca [IGMP Thread] BcmIgmpThread::Starting Igmp Thread...: (IGMP Thread)
0x007254d4 [Motorola Standby Switch Thread] BcmStandbySwitchThread::ThreadMain: (Motorola Standby Switch Thread) Standby switch was pressed!
0x007254d4 [Motorola Standby Switch Thread] BcmStandbySwitchThread::ProcessSwitchEvent: (Motorola Standby Switch Thread) Standby switch disabled in nonvol; ignoring event.
Logging event: TLV-11 - Illegal Set operation failed
Sending syslog message from IF 1 to 192.168.1.10:
<130> CABLEMODEM [DOCSIS]: <73040200> TLV-11 - Illegal Set operation failed
SB5102 CM Event Log w/ BRCM Factory Support sending deferred async messages...
Sending syslog message from IF 1 to 192.168.1.10:
<130> CABLEMODEM [DOCSIS]: <84000200> SYNC Timing Synchronization failure - Failed to acquire FEC framing
Sending syslog message from IF 1 to 192.168.1.10:
<133> CABLEMODEM [Motorola Corporation]: <2300955725> Ethernet link up - ready to pass packets
Sending syslog message from IF 1 to 192.168.1.10:
<130> CABLEMODEM [DOCSIS]: <84000100> SYNC Timing Synchronization failure - Failed to acquire QAM/QPSK symbol timing
Sending syslog message from IF 1 to 192.168.1.10:
<130> CABLEMODEM [DOCSIS]: <84000100> SYNC Timing Synchronization failure - Failed to acquire QAM/QPSK symbol timing
Sending syslog message from IF 1 to 192.168.1.10:
<130> CABLEMODEM [DOCSIS]: <84000100> SYNC Timing Synchronization failure - Failed to acquire QAM/QPSK symbol timing
Sending syslog message from IF 1 to 192.168.1.10:
<130> CABLEMODEM [DOCSIS]: <84000100> SYNC Timing Synchronization failure - Failed to acquire QAM/QPSK symbol timing
Sending syslog message from IF 1 to 192.168.1.10:
*********************************
********* *********
********* EDITED *********
********* *********
*********************************
Sending syslog message from IF 1 to 192.168.1.10:
<130> CABLEMODEM [DOCSIS]: <84000100> SYNC Timing Synchronization failure - Failed to acquire QAM/QPSK symbol timing
Sending syslog message from IF 1 to 192.168.1.10: