Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
sb6190 serial console error input
#2
(31-08-2017, 04:42 AM)christianrodher Wrote: Input is doing gibberish and random characters... anyone encounter this before and fix it?

serial console logs:
Code:
NPCPU Only Mode = 0


Cat Mountain D0 - Boot Ram.
Version: 0.1.16 (Apr 10 2014, 18:52:35)
Boot Param memory dump:
[0x1FFC] - 0x00010016
[0x1FF8] - 0x00000001
[0x1FF4] - 0x00000001
[0x1FF0] - 0x00000001
[0x1FEC] - 0x00000001
[0x1FE8] - 0x08000000
[0x1FE4] - 0x08000000
[0x1FE0] - 0x00200000
[0x1FDC] - 0x00220000
[0x1FD8] - 0x00240000
[0x1FD4] - 0x00040000
[0x1FD0] - 0x00280000
[0x1FCC] - 0x00280000
[0x1FC8] - 0x00020000
[0x1FC4] - 0x00000000
[0x1FC0] - 0x00000000
[0x1FBC] - 0x00000000
[0x1FB8] - 0x00000000
[0x1FB4] - 0x00000000
[0x1FB0] - 0x00000000
[0x1FAC] - 0x00000000
[0x1FA8] - 0x00000000
[0x1FA4] - 0x00000000
[0x1FA0] - 0x00000000
[0x1F9C] - 0x06050201
[0x1F98] - 0x09030807
[0x1F94] - 0x0E0D0C0A
[0x1F90] - 0x00000001
[0x1F8C] - 0x0000000C
[0x1F88] - 0x00030111
[0x1F84] - 0x00201000
[0x1F80] - 0x00000070
[0x1F7C] - 0x00221000
[0x1F78] - 0x00008000
[0x1F74] - 0x00000020
[0x1F70] - 0x00180000
[0x1F6C] - 0x00010000
[0x1F68] - 0x00190000
[0x1F64] - 0x00009400
[0x1F60] - 0x00199400
[0x1F5C] - 0x00065400
[0x1F58] - 0x001FF000
[0x1F54] - 0x00000800
[0x1F50] - 0x001FF800
[0x1F4C] - 0x00000800
[0x1F48] - 0x001FE800
[0x1F44] - 0x00000800
[0x1F40] - 0x00000001
[0x1F3C] - 0x00000000
[0x1F38] - 0x00010000
[0x1F34] - 0x00000000
[0x1F30] - 0x00000000
[0x1F2C] - 0x00000000
[0x1F28] - 0x00000000
[0x1F24] - 0x00000000
Load U-Boot from eMMC/NAND Flash
eMMC/NAND copy from 0x00240000 to 0x49FB0000 (len:262144).
Done.


U-Boot 1.2.0 (Dec 24 2015 - 08:28:48)
PSPU-Boot 2.2.0.45

DRAM:  128 MB
Flash:  0 kB
MMC:   sdhci_puma6: 0
MMC info:
  Manufacturer ID: 0
  OEM ID: 0
  Name: MMC128
  MMC version 4.4
  High Capacity: No
  Dual Data Rate (DDR): No
  Bus Width: 8-bit
  Clock: 50000000
  Rd Block Len: 512
  Capacity: 112.4 MB (117833728 bytes)
In:    serial
Out:   serial
Err:   serial
WARNING: BOOTPARAMS_AUTOUPDATE is equal to 'off', u-boot do not update Boot Parameters automatically.
Board-Type:  harborpark
AEP:         Disable
Boot Device: mmc
ACTIMAGE:    1
Press SPACE to abort autoboot in 2 second(s)
=>  <INTERRUPT>
=> lkJsFsFlaOkJj%daOsFd <INTERRUPT>
=>

It may not serve much, but did you check the connection status to the GND point? It has a uboot version of 2015, relatively modern bone and possibly hood.
Reply


Messages In This Thread
RE: sb6190 serial console error input - by 0xff - 31-08-2017, 05:02 PM

Forum Jump:


Users browsing this thread: 1 Guest(s)