Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
tried to update and bricked dpc2100r2 modem helppp
#1
modem dpc2100r2 I flashed using the rj connector and decided to go ahead and upgrade . i used legal modem to get the newest file haxorware11rev39-DIAG.bin and used the modem upgrade option to upload it.suddenly my page was replaced by page not found error. now cant do anything so i took modem apart to flash parralell with jtag. **** no pins to plug the connector to. now what?? any idea why this happend?any way to fix this?? please help me cause i need to uncap my isp aint worth crap as is.
Reply
#2
solder the header
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply
#3
thats an awful small space and my soldering pen is for crap the holes are factory soldered over and i dont wanna screw it up what about using the four pin header isnt that for serial? if i bought a usb jtag?
Reply
#4
(01-11-2012, 12:29 AM)rogerreed Wrote: modem dpc2100r2 I flashed using the rj connector and decided to go ahead and upgrade . i used legal modem to get the newest file haxorware11rev39-DIAG.bin and used the modem upgrade option to upload it.suddenly my page was replaced by page not found error. now cant do anything so i took modem apart to flash parralell with jtag. **** no pins to plug the connector to. now what?? any idea why this happend?any way to fix this?? please help me cause i need to uncap my isp aint worth crap as is.

#1 did you make a back up of your unit before making modifications?
you will need the bin, after you are able to debrick it.
#2 I have debricked this unit using the Poke method that is used
to unbrick the sb5100
Yes, you will need to solder 8 pins into unit. Just get some solder
wick, and remove the current solder. Then solder your new pins.
Reply
#5
usb serial cables are very cheep on ebay about $2 that should be able to fix it, if you want to go that way
another way is to get a solder sucker to clear out the holes (depends on how good you are at soldering)
and the last way is just solder some short wires to the solder points (you can do this on the backside as it's easier) and shove the wires into the jtag connector
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply
#6
well i ordered a USB to UART TTL USB to COM Cable Adapter Module from ebay now i gotta go learn about telenet. I did install haxor back when i first joined sucessfully but modem was lost during move but that one had the 8 pin header in it.guess this one is gonna be done the hard way. any sugestions on a really noobie telenet primer.I have never used it before.
Reply
#7
http://www.ebay.com/itm/1pcs-PL2303HX-US...2a256cdc9c

there is the address of the usb adapter i got. problem is it basically says the same as the method started saying using the ethernet cable method. connection timed out. it didnt start saying that until i tried to upgrade from the file i had installed.at first haxor was there because i was able to connect and go to all the different pages.i have no idea whats happening now.it wont see the modem with usb or ethernet cable either one.please someone help me figure this out.remember there was a time when you were a beginner too.i installed haxor before using jtag when i first joined.now this.i tried telenet and putty both to no avail and im pulling my hair out. ps using ethernet didnt give a chance to backup but i have another modem i can get one from if i get this figured out.
Reply
#8
can you still see the bootloader in telnet, if so reflash
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply
#9
it never connects in telenet r putty it times out thats the problem i cant get in to do anything and dont know why
Reply
#10
you are connecting via the com port and not 192.168
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)