Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
sb5101 Online
#1
hi my sb5101 has a valid mac from a DPC2100R2 that is on comcast.but my sb5101 recently stop going online.the ONLINE light just keeps blinking and gets stuck on "registration complete" any suggestions please how can i get it online again. thanks in advance

keeps giving me this mesage "Critical R004.0 Received Response to Broadcast Maintenance Request, But no Unicast Maintenance o"

dnt kno what it means and my ONLINE light keeps blinking and stuck on "registration complete"
Reply
#2
a vaild mac you say so did you change your spoof to match the dpc2100rc mac? but anyway, are you enjoying the new security
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply
#3
I have same issue since last night. I changed securuty to BPI+Bypass and status goes to operational but comcast does not give ne IP so router shows as 0.0.0.0
Reply
#4
(21-04-2011, 07:20 PM)drewmerc Wrote: a vaild mac you say so did you change your spoof to match the dpc2100rc mac? but anyway, are you enjoying the new security


yes it's a valid mac....i changed my bpi settings since the mac used to work on bpi 1.0 with this mac i used from dcp modem i got it to go to operational but still no internet.any suggestions?
Reply
#5
you say (why am i starting with that again?) about bpi but still no mention of the spoof?
anyways if the spoof is the correct and matches, next thing i'd do is extract the nonvol from the webby and flash that
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply
#6
(22-04-2011, 06:19 PM)drewmerc Wrote: you say (why am i starting with that again?) about bpi but still no mention of the spoof?
anyways if the spoof is the correct and matches, next thing i'd do is extract the nonvol from the webby and flash that

So I gotta extract the original 2mb firmware from dcp modem that I'm paying for on camcast then extract the Certs from it to flash it back in my 5101 modem?and if this is the case how would I do this please.?
Reply
#7
http://www.haxorware.com/forums/thread-823.html
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply
#8
(23-04-2011, 06:53 AM)drewmerc Wrote: http://www.haxorware.com/forums/thread-823.html

Umm so do I need to open and connect my black cat to my dcp modem to extrac the Certs? Or do I just need the usbjtag software only?I kno I need to connect. My blckcat USB Utah to my 5101 flash the Certs in..correct me if I'm wrong cuz dnt say on that thread u showed me .thanks
Reply
#9
yes you connect your blackcat to your webby and dump it then use usbjtag software to extract the nonvol from the dump (haxor can flash this to your sb5101)

__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply
#10
well after trying this i manage to break my dcp modwm i pay for with comcast....a tech came over my house and replaced it with a Ubee Model:U10c035 modem.i guess is a Docsis 3.0 modem Smile cuz has "D3.0" on the modem.anywayz my question is can i still use the blackcatusb on this modem?
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)