Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
how to change Upstream Modulation???
#1
Hi all

how to change upstream modulation because now SCDMA use but i need QAM16

Downstream
Frequency 417 MHz
Status Locked
Annex DOCSIS
Modulation QAM256
Symbol Rate 5360537 sym/sec
Receive Power 13.5 dBmV
Signal to Noise ratio 42.4 dB

Upstream
Frequency 35 MHz
Channel ID 10
Status Ready
Mode SCDMA <<------------------------- this is how to change???
Symbol Rate 2560000 sym/sec
Transmit Power 50.2 dBmV

thx for help me everybody Smile
Reply
#2
why would you need to it's part of the docsis spec (2.0 i think)
as far as i know the only way to change it would be use a docsis 1 mac (but i could be wrong)
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply
#3
(29-09-2009, 04:11 PM)drewmerc Wrote: why would you need to it's part of the docsis spec (2.0 i think)
as far as i know the only way to change it would be use a docsis 1 mac (but i could be wrong)

how to change docsis 1 mac and how to change upstream mode?

i'm from hungary my isp is fibernet and if upstream mode SCDMA then ~300KB/s upspeed but, if upstream mode QAM16 then ~800KB/s upspeed, that's why i need QAM16 upstream mode

incidentally with factory firmware QAM16 use

i hope understandable write but i low speak english :S

thx for help me
Reply
#4
you can try forceing a config or use a better mac
usseing this http://www.sbhacker.net/forum/index.php?...owfile=345 to get macs

more info http://www.sbhacker.net/forum/index.php/...tion-file/
http://www.sbhacker.net/forum/index.php/...r-address/
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply
#5
(29-09-2009, 08:41 PM)drewmerc Wrote: you can try forceing a config or use a better mac
usseing this http://www.sbhacker.net/forum/index.php?...owfile=345 to get macs

more info http://www.sbhacker.net/forum/index.php/...tion-file/
http://www.sbhacker.net/forum/index.php/...r-address/

i use force config this not problem, only upstream modulation with change.

Configuration file
Name unl.cfg
Size 92 bytes
Compliance DOCSIS 1.1

how to force the modem to QAM16 upstream mode?

any command in console or setting?
Reply
#6
there's no command it's part of the config that is downloaded only way to change is change the config or mac
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply
#7
i not fully understand. the config into is it that change upstream mode?

because then what write in the config?
Reply
#8
the config is downloaded when the modem registers with the network it contains the settings needed to get online
the config that is downloaded is matched to the mac
[Image: attachment.php?aid=72]


Attached Files Thumbnail(s)
   
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply
#9
i know i know, but where in upstream mode setting?
Reply
#10
i'll say it again you need to change the config or the mac
run the program in the picture above (without a router being in the way) let it run for a while it'll give you some different configs's that you can try to force
or run the program on a differant node/ubr and it will give you differant macs to try
__________________________________________________________________________________
******new discord chat link https://discord.gg/5BQQbsb*******
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)